Browse all practice questions for the Minnesota Contractors Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Minnesota Contractors Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • According to the IRC, how far should a masonry chimney extend above any portion of the building that is within 10 horizontal feet of the chimney?
  • What is the ground snow load in Duluth?
  • Which of the following is NOT a responsibility of the Commissioner regarding contractors?
  • How do we protect the underside of a stairway?
  • A contractor is installing wood board siding to the exterior of a house. The fasteners must penetrate the studs a minimum of?
  • What should a contractor do if a building permit application is denied?
  • Under what condition may a building official enter the premises?
  • Which of the following is allowed on rebar?
  • Which authority manages the issuance of building permits and inspections?
  • If a contractor changes his name, the contractor must notify the Commissioner of the change no later than how many days after the change?
  • What is the minimum R-value requirement for ceilings in the northern Minnesota climate zone?
  • What is the minimum dimension you should extend siding below the sill plate?
  • A contractor is building a two-story house with a gable roof. How many squares of shingles are required for this roof?
  • What does the term "slump" refer to in concrete work?
  • How many nails are used to attach diagonal, let in, wood bracing to a stud?
  • What is the minimum to maximum air gap when installing brick veneer?
  • Which of the following insurance items are required by contractor license law? Choose all that apply.
  • What is required for a handrail on stairs according to safety standards?
  • What is the minimum number of stud spaces that let in bracing must cross when wall construction uses studs 2 feet on center?
  • What is the minimum size for access to an attic space?
  • How thick should exterior wall insulation be for optimal energy efficiency?
  • If no action is taken, how long does a permit last?
  • What table would you use to calculate the span for a joist that also spans cantilevers?
  • What is the minimum percentage requirement for continuous ventilation?
  • What is the primary purpose of the critical path method in project analysis?
  • How do interconnected smoke alarms benefit safety in a residential setting?
  • What is the minimum gauge of galvanized valley flashing?
  • What is the required spacing when applying wood shingles?
  • In which type of framing construction do the studs extend from the foundation to the roof?
  • What is the MOST important element of a construction contract?
  • When nailing asphalt hip and ridge shingles, what are the required nailing positions using the standard 5-inch exposure?
  • What must parties to a written contract do before they sign the contract?
  • What is the minimum insulation required in ceilings with no attic when this area is less than 20% of the insulated ceiling?
  • How many cubic yards of concrete will be used in pouring a slab with dimensions: 72 feet 3 inches x 88 feet 6 inches x 6 inches deep?
  • Which statement is TRUE regarding the warranty on a new home for the second homeowner?
  • What is the minimum R-value requirement for above-grade walls in an energy-efficient building?
  • What is the minimum number and size face nail required to attach a 1 inch by 4 inch let in bracing to each stud and plate?
  • When using multiple interconnected smoke alarms, what response mechanism is activated?
  • What is the minimum thickness of a concrete floor?
  • If poor flashing causes a roof leak six months after occupancy, who is liable for the repair?
  • What authority does the Commissioner hold regarding civil penalties?
  • When using multiple interconnected smoke alarms, how do they respond to smoke?
  • Residential building contractors must warrant that the dwelling will be free of defects from faulty installation of plumbing, electrical, and heating and cooling systems for which period?
  • Which installation aspect is crucial for maintaining ventilation in an attic?
  • Why is it important to have the correct footing depth?
  • A masonry fireplace with an opening of 6 square feet or more shall require minimum hearth extensions of _______________ inches to each side of the opening and a minimum of __________ inches to the front of the opening.
  • What are the minimum, net clear dimensions of a window well used for an emergency escape?
  • What document must be filed to enforce a mechanic's lien?
  • What is the maximum mortar thickness of the initial bed joint when installing brick on a concrete slab?
  • What is the minimum specification for weather-resistant sheathing paper used as a wall covering?
  • What authority does the building official have in relation to building codes?
  • What is the primary purpose of a sprinkler system in buildings?
  • Chimney requirements state that the chimney must extend at least 2 feet above any portion of the building within how many feet of the chimney?
  • The lowest edge of untreated siding shall be a minimum of how high above grade?
  • What distinguishes an active radon system from a passive one?
  • Who is responsible for enforcing land use zone requirements?
  • Why is it necessary for contractors to maintain insurance documentation?
  • An owner has agreed to make periodic payments to the contractor during the construction period. These payments are known as what?
  • When must a skylight be mounted on a curb extending 4 inches above the plane of the roof?
  • Who is responsible for inspecting your drywall?
  • A contractor or any person performing contracting work in Minnesota must be licensed prior to obtaining a permit for the work. Which of the following agencies issues the license?
  • What is the minimum footing depth required in the Twin Cities?
  • Where do you apply for a building permit?
  • What is the default fenestration U-factor rating for metal frame, with thermal break, double-pane skylights?
  • How should you drive the nails that hold aluminum siding to the wall sheathing?
  • What is the required bearing length for a lintel over a masonry fireplace, supporting a masonry finish?
  • What does a provisional permit allow a contractor to do?
  • What type of liability is a general contractor responsible for?
  • What is the primary purpose of interconnected smoke alarms?
  • Which of the following options is NOT considered a code issue?
  • Which of the following is NOT included in a comprehensive municipal plan?
  • If a contractor begins work on a building before a permit is issued, what action may be taken?
  • Where does the birdsmouth cut on a rafter rest?
  • In structural framing, what does a stringer primarily support?
  • Which document signifies that a building can be legally used for its intended purpose?
  • What is the required thickness of concrete for a residential driveway?
  • How much do ceiling joists overlap when meeting over a girder or partition?
  • What action can the building official take if work is NOT proceeding to code?
  • What is the remedy for a homeowner if the contractor does not correct a known defect?
  • A contractor is installing 6 inch wood siding to the exterior of a house. The siding must overlap a minimum of?
  • Who has the authority to issue contractor licenses in Minnesota?
  • Where should nails be placed in exterior bevel siding?
  • What is the minimum size of a footing required under a load-bearing wall in new construction?
  • What is the actual dressed size of a 2 inch by 4 inch stud?
  • To apply for a permit, which department must provide the permit application?
  • You have a total roof area on each side of a gable roof of 44 feet by 18 feet. The shingles chosen have three bundles per square. How many bundles of shingles are needed to cover this roof, NOT including waste?
  • General liability insurance covers which of the following?
  • In a fire suppression system, what is the purpose of a flow rate test?
  • Which document outlines the boundaries and key features of the construction site?
  • What is the minimum number of inches wood siding must extend below the sill plate?
  • What is the ground snow load in the Twin Cities?
  • Which of the following documents describes the types of materials needed for a contract?
  • What is the maximum tolerance between the centerline of the horizontal framing member and the vertical framing member when using steel floor framing?
  • Which of the following types of material and thickness is required to retard the flow of soil gases - radon - into a building?
  • When is payment due to the homeowner who has won a Recovery Fund judgment against a contractor?
  • Base material under a below grade concrete floor, if required, shall consist of?
  • What is the maximum floor area for tool sheds to be exempt from requiring a building permit?
  • Contractor license law does NOT require contractors to display their license numbers on which of the following?
  • Joist framing into a girder is acceptable if supported by?
  • What should be included in a building inspection checklist?
  • What is the required distance of a sprinkler from a heat source in residential kitchen areas?
  • The recommended placement of reinforcement for footings is in the?
  • What is the minimum bearing allowance where a built-up wood girder is supported in the foundation walls?
  • When doubling top plates, what is the required distance for staggering joints?
  • According to the Fair Labor Standards Act, how is a workweek defined?
  • What is a key requirement for contractor licenses in Minnesota regarding renewals?
  • If you have a finished floor to ceiling height of 8 feet and a double plate at the top and single plate at the bottom, how long do you cut the studs?
  • Which group is NOT required to be licensed as contractors?
  • When is it required to double a header joist and trimmer joist?
  • What is the sequence of attaching gypsum wallboard at the ceiling intersection?
  • Which of the following is true regarding payments from the contractor recovery fund?
  • When must contractors notify owners of their lien rights?
  • What is the purpose of an integration clause in a contract?
  • Who has final interpretive authority for all codes adopted, except for plumbing and electrical?
  • What is the maximum allowable U-factor for windows in Minnesota?
  • If you have a fireplace opening that is 2 1/2 feet high and 3 1/2 feet wide, how far out in front of the fireplace shall the hearth extend?
  • When a subcontractor requests an owner's name and address, by when must the contractor provide that information?
  • To cover an area of 52 feet by 74 feet using 1/2 inch by 4 foot by 8 foot sheets of plywood, how many sheets will be needed?
  • What legal requirement is associated with changes in construction related to general liability insurance?
  • When installing aluminum siding, how should you space joints around windows and doors?
  • What must every contractor do before initiating construction according to local statutes?
  • A permit may be issued for construction of part of a building before the construction documents for the whole building are submitted. What is this called?
  • What is the minimum hearth extension depth required for a fireplace with an opening less than 6 square feet?
  • What is the maximum thickness for the joints in firebrick?
  • What type of insulation is typically recommended for basement wall applications?
  • What is the maximum diameter hole that may be drilled in a 2 inch by 12 inch joist?
  • Untreated siding shall be no closer than?
  • What action may the Commissioner take if someone is fraudulently using another builder's license number?
  • If the first row of roof sheathing is started with a full sheet of plywood, how should the second row start?
  • What is the minimum footing depth in St. Louis County, Minnesota?
  • How many coats are required when installing gypsum over metal lath or wire mesh?
  • A new two-story house has basement dimensions of 52 feet by 28 feet, with a 20 foot by 22 foot attached garage. How much concrete will be required to pour the basement walls?
  • An owner decides to change the location of several interior walls in a building now under construction. What part of the existing contract addresses this issue?
  • What is the purpose of a site plan?
  • By how much may the greatest riser height exceed the minimum?
  • A homeowner files a claim for a severely cracked garage floor that one of your subcontractors installed six months ago. Who is liable for the claim?
  • What roof truss design is MOST likely specified for a new home with a cathedral ceiling?
  • When finishing concrete, the movement of water to the top surface is known as what?
  • Fresh air leaks into a house through cracks around windows, doors, and framing. The process is called:
  • What is the minimum airspace separation of brick from sheathing in an exterior application?
  • The contractor's offer to the owner should include which of the following?
  • What is the header size required over a 2 foot, 8 inch door?
  • What document must a contractor submit when changing their business name?
  • Which factor does NOT influence the ground snow load in a given county?
  • The contractor recovery fund is administered by which entity?
  • Fasteners shall be spaced NOT less than how far from edges and ends of gypsum wallboard?
  • Every other year, continuing education credits must include at least one hour of which type of training?
  • The upright member found under the handrail and attached to the tread is called what?
  • What is the required sprinkler water supply capacity for a one-story structure with less than 2,000 square feet?
  • What is the primary purpose of a vapor retarder?
  • What is the range of air entrainment required in concrete that is subject to thawing and freezing?
  • At the juncture of the roof surface and a vertical surface (wall), the flashing shall NOT be less than?
  • Select four of the following items that are used to determine the flow rate for each sprinkler.
  • Which type of roofing material usually requires fewer fasteners for installation?
  • Perpendicular application of sheetrock is preferred where fire code permits because it:
  • Who has the legal right to file a lien under the Minnesota mechanic's lien law?
  • If a qualifying person leaves a company, how long can the temporary license remain valid?
  • Concrete is being placed in an area with recurrent freezing and thawing. Which admixture should be used?
  • Which one of the following types of roofing can be used to make closed valleys?
  • What must be issued by the building official before a building can be inhabited?
  • What role does the building official primarily serve in construction licensing?
  • When did the current Minnesota statutory home warranty law come into effect?
  • Plumbing roof vents must extend a minimum of how far above the roof?
  • What is the minimum clear opening height of an emergency escape window?
  • Which of the following is NOT typically a part of project planning and scheduling?
  • Where must subcontractors file a claim against a property owner?
  • What is the minimum pipe size for any sprinkler?
  • What can be a consequence if a homeowner does not follow the Notice and Opportunity to Repair Law?
  • What is the minimum compressive strength of concrete for footings?
  • Which of the following is TRUE of a contractor who operates without a valid license?
  • Why is project planning and scheduling considered important?
  • What is the minimum number of nails recommended for a standard framing connection?
  • To collect on a mechanic's lien, action must be commenced within how long after the date of the last item recorded in the lien statement?
  • Which material is most commonly used for framing walls in residential construction?
  • Which one of the following is NOT a component of an exterior wall?
  • A stairway with 16 risers has a total of 9 feet 2 inches between finished floors. What is the rise per unit?
  • What is the purpose of using air-entrained concrete?
  • What is the minimum requirement for drainage slopes that move water away from a foundation?
  • What is the minimum insulation requirement for above grade mass wall in Duluth?
  • Which of the following fenestration exemption statements is NOT true?
  • What is the maximum time frame within which a contractor must respond to a homeowner's warranty claim?
  • Which type of concrete finish is typically used to enhance the aesthetic appearance of a surface?
  • What must a contractor and customer do before signing a construction contract?
  • What is the minimum diameter anchor bolt that may be used without a noncorrosive coating?
  • What type of warranty typically covers structural defects in a new home?
  • What is the typical installation requirement for roofing underlayment?
  • What is the maximum amount typically covered under contractor insurance policies for general liability?
  • What is the minimum distance between smoke alarms in a residential setting?
  • When is an artificial light source NOT required at the top or bottom stair landing?
  • Ventilators must be provided with corrosion resistant wire mesh; what is the maximum size opening?
  • The energy heel on a roof must be at least:
  • When installing the sill plate to the foundation, what is the maximum distance between 1/2 inch bolts?
  • Which of the following materials is generally NOT recommended for insulation in high-moisture areas?
  • What should a contractor do immediately after making emergency repairs?
  • What is the minimum bearing for a wood beam resting in a poured concrete wall notch?
  • What is the minimum coverage limit required for general liability insurance?
  • Modular (standard size) blocks are usually about 7 5/8 inches high by 15 5/8 long in order to allow for?
  • Who decides which inspections are required when a permit is issued?
  • What is the minimum nailing requirement for toenailing a stud to the sole plate?
  • What is the maximum weather exposure for a 16 inch single course wood wall shingle?
  • Who is responsible for establishing standards and procedures to regulate erosion control?
  • Which of the following materials is NOT recommended for drywall in garage applications?
  • Where must you install the vapor retarder?
  • In new construction, when does the homeowner's warranty start?
  • In what instance is a contractor's emergency repair permissible without a permit?
  • Which of the following documents does the contractor use to determine the quantities of materials needed for the contract?
  • What is the required spacing between panels when installing roof sheathing?
  • What is the ground snow load requirement in Washington County?
  • What nail spacing is used for fasteners when hanging vinyl siding?
  • How many fasteners are required for installing 36-inch asphalt shingles?
  • What is the maximum allowable height for a stair with a single flight?
  • What is the fenestration U-factor requirement for a skylight in the southern Minnesota climate zone?
  • Where should roof sheathing be stored on the roof prior to installation?
  • What is a primary reason a contractor might face revocation of their license?
  • When applying wood shingles at less than a 12/12 slope, how far should the roof valley flashing extend from the center line?
  • What is the roof snow load in the Twin Cities?
  • How far can the top of the exterior landing be below a threshold if the door swings away from the landing?
  • What is the basic purpose of a written contract between the owner and the contractor?
  • What type of screw is used to fasten gypsum wallboard to a metal stud?
  • What is an acceptable method for securing roof sheathing?
  • What is the name of the rafter that provides support between other rafters?
  • Before commencing construction, what must builders ensure they have obtained?
  • Which of the following must contractors provide when executing a contract with a property owner?
  • Concrete footings for a one floor house must be a minimum of how thick and wide?
  • If there is an emergency situation, what is required of the contractor regarding a permit?
  • What is the minimum gauge of galvanized valley flashing?
  • How many days is a contractor's temporary license valid after the contractor's qualifier leaves?
  • What does the Minnesota minimum wage law generally stipulate regarding workweeks?
  • Unless a lien statement is properly filed and recorded, mechanic's liens cease how long after the last item is furnished?
  • Which type of insulation is most commonly used in exterior walls?
  • What thickness of type X gypsum is required on a garage ceiling below a living space?
  • What is the recommended spacing for under boards in board and batten siding?
  • What is the actual dressed size of a 2 by 8?
  • What type of joint is typically used to connect two framing members at a right angle?
  • Which is the correct way to install steel siding?
  • A lien waiver primarily protects the owner from which issue?
  • When installing tongue and groove plywood combination subfloor underlayment, how does the second row of panels differ from the first?
  • Which of the following is NOT required as part of an application for a Minnesota contractor license?
  • The purpose of a written change order is to:
  • When installing insulation between floor joists in a crawl space, the vapor retarder:
  • What is the BEST rule to follow when notching trusses?
  • What is one sign of a failing roofing system?
  • When laying out exterior siding, the vertical distance to be covered is determined by measuring from the underside of the soffit to a minimum of how far below the bottom sill plate?
  • What is the typical use for a double top plate in framing?
  • What is the penalty for failing to comply with the requirements of the Minnesota mechanic's lien law?
  • The tool used to produce a rounded edge on a slab to prevent chipping is a?
  • During what period does the contractor remain liable for work done under warranty?
  • What is a primary component of a municipal plan?
  • According to the Fair Labor Standards Act, what is the maximum number of hours a 14-year-old can work in a school week?
  • When do lien rights attach?
  • Which law outlines the conditions of employment for minors?
  • What is the range of distance from a heat source for an intermediate temperature sprinkler near a kitchen range top?
  • How many days after a change must written notice be given to the Commissioner regarding business location, personal name, or address?
  • When attaching a wood ledger board to a structure, the IRC provides fastener information for which type of fastener?
  • How does a building inspector assess attic insulation?
  • What is the liability of a general contractor concerning subcontractors?
  • What is the minimum height above roof for a single radon vent pipe?
  • By what date must contractors complete their continuing education credits for timely license renewal?
  • How far must a masonry chimney extend above a flat roof that is within 10 horizontal feet?
  • What is the minimum end bearing of a joist on wood or metal?
  • Who is required to comply with applicable codes during construction work?
  • What is the required minimum vertical headroom clearance for stairways in new construction?
  • The Commissioner may impose civil penalties up to how much per violation?
  • When should a concrete slab be cured to achieve maximum strength?
  • If there is no agreement between a homeowner and contractor regarding a warranty claim, which process must be followed prior to legal action?
  • What is the recommended spacing at corner joints when installing steel siding?
  • What are the continuing education requirements for holders of a Minnesota contractor's license?
  • Within the guidelines of the Contractor Recovery Fund, what is the maximum recovery per claimant?
  • When applying for a permit, which entity must you pay a fee to?
  • What is the minimum air space permitted at the location of vent between the insulation and the roof sheathing?
  • What is the lowest member of the frame structure that rests on the foundation?
  • Which of the following are essential elements of a contract?
  • According to Minnesota minimum wage law, when is overtime payment required?
  • How do you increase the compressive strength of mortar containing lime and Portland cement?
  • When can a bedroom be accessed directly from the garage?
  • What action might be taken for a serious violation of building codes?
  • If a homeowner receives a payment out of the Recovery Fund, what is an automatic remedy against the licensee?
  • Where is metal reinforcement positioned in a concrete basement floor?
  • What process would be used on concrete to produce a nonslip surface?
  • Contractors are required to pay what type of fee regarding the continuing education fund?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy